Wood Be Retired
  • Home
  • About
  • Watercolors
    • Available Framed Watercolors
    • Giclee Prints
  • Woodwork
    • Fine Art Frames
    • Photo Frames
    • Casual Furniture
    • Woodcrafts
    • Custom Woodwork
  • Contact
  • Blog

Back At It!

8/27/2018

0 Comments

 
Barbara and I are back in town and settled in after spending a week in Alberta Canada on a great Roads Scholar trip.  We saw many spectacular vistas in Banff, Lake Louise and Jasper in spite of the smoke blowing in from the many fires in British Columbia.  You can see the smoke in the background of the second and third pictures.
Picture
Picture
Picture
I have again applied to participate in this year's Durham Craft Market Holiday Market.  In anticipation, I have begun to put together some cutting boards and thought you might enjoy seeing some pictures of the process.
Picture
First I cut hardwood into 3/4" strips of varying widths.
Picture
Then glue glue-up blanks of various lengths depending on the best utilization of materials. Note I have glued on sacrificial runners cut from 2X4 studs that are about 8-10" longer than the board.
Picture
I run the blanks repeatedly though a surface planner to make both faces of the blank smooth and parallel. The sacrificial runners prevent the planner from cutting low areas (called snipe) in both the front and rear edge of the blanks. If I don't use the runners, I either have to cut off the low areas or spend a lot of time sanding down the high area in the middle.
Picture
The sacrificial runners are cut off the ends and sides of the blanks.
Picture
Yielding blanks ready to be cut and glue in curved contrasting hardwood strips.
Picture
Thin strips of hardwood approximately 3/4" wide are repeated run though the surface planner to an final depth of 1/16". That depth is critical so that the strips are approximately the same depth as the width of the kerf that is cut in the blanks creating the curved inlays. If the strips are too thick, the hardwood strips in the final board will not line up appropriately.
Picture
I've made a bunch of strips of varying lengths and hardwoods in anticipation of the next steps.
I'll post another blog when I have gone on to the final steps so you can see the end of the process.

A lot of waste is created when cutting the original 3/4" strips to make the board blanks.  I thought if I squared these waste strips to 3/4" on each side and approximately 1.5" long I might be able to make an end grain trivet or cheese block.  The glue-up proved to be difficult but I like the concept.  I may try it again but using 2" squares to make a full size end grain cutting block.  Do you like to the concept?  The test block below is maple, walnut and jatoba woods.
Picture
0 Comments

"St. John's" Accepted to WSNC Annual Show

8/2/2018

0 Comments

 
Picture
I am very pleased to announce that my watercolor "St. John's" has been accepted to the 2018 Watercolor Society of North Carolina Juried Exhibition!  It was one of 70 accepted (of 262 entered) by this year's renowned juror, Iain Stewart.  The exhibition opens on Sunday October 7 at 2:00 PM at the Florence Thomas Arts School in West Jefferson.  The exhibition will rund through November 16, 2018.  My thanks to Ian for selecting "St. John's" as part of this year's exhibition. 
0 Comments
    Picture

    Author

    John Schwartz - watercolorist and woodworker.

    Archives

    January 2021
    May 2020
    April 2020
    February 2020
    August 2019
    April 2019
    March 2019
    January 2019
    December 2018
    November 2018
    October 2018
    September 2018
    August 2018
    July 2018
    December 2017
    November 2017
    September 2017
    August 2017
    July 2017
    April 2017
    March 2017
    January 2017
    September 2016
    March 2016
    February 2016

    Categories

    All

    RSS Feed

  • Home
  • About
  • Watercolors
    • Available Framed Watercolors
    • Giclee Prints
  • Woodwork
    • Fine Art Frames
    • Photo Frames
    • Casual Furniture
    • Woodcrafts
    • Custom Woodwork
  • Contact
  • Blog